-
82"x14', (2) 3500# EZ-Lube brake axles, 50" square tubing forward folding spring assist gate, 2"x 1.5" square tubing uprights, 2"x2" square tube top rail, 4" channel iron tongue, HD diamond plate steel fenders, new radial tires, sealed wiring harn...Over 4 weeks ago on RVUSATools
-
Up for sale is a 1998 race ready honda 300ex. This has had all new parts except for basically the frame! It is very quick and no short cuts have been taken. Well taken care of. The new engine has maybe at most ten hours. Oil and filter changed eve...Over 4 weeks ago on ClazTools
-
83"x14', (2) 3500# brake axles, 2' steel dovetail, 3' gate, (5' low load angle), gorilla lift (let gate down & lift up with one hand easily), LED lights, sealed wiring harness, cold weather harness, special order pink powder coat paint, adjustable...Over 4 weeks ago on RVUSATools
-
* 3" x 2" Aluminum Angle Extrusion Frame * 3" x 2" Aluminum Angle Extrusion Crossmembers (Single Axle) 4" Aluminum Triple Tube Tongue (Single Axle) * 2" x 1-1/2" Aluminum Extrusion Tube Uprights * 2" x 2" Aluminum Tube Top Rail * 2" A-Frame Posi-L...Over 4 weeks ago on RVUSATools
-
Made in the U.S.A., allows dirt to fall through, Independent grapple tines, 2"x10" cylinders, 9500# of grappling force, 1/2" steel, reinforced quick attach, fully protected hoses, covered cylinders, fully greasable hinge points, oversized greasabl...Over 4 weeks ago on RVUSATools
-
* 3" x 2" Aluminum Angle Extrusion Frame * 3" x 2" Aluminum Angle Extrusion Crossmembers (Single Axle) * 4" Aluminum Triple Tube Tongue (Single Axle) * 2" x 1-1/2" Aluminum Extrusion Tube Uprights * 2" x 2" Aluminum Tube Top Rail * 2" A-Frame Posi...Over 4 weeks ago on RVUSATools
-
* Steel Angle Frame & Crossmembers * 2" x 1-1/2" Steel Tube Uprights * 2" x 2" Steel Tube Top Rail * (2) 2" x 5' Side Ramp Conversions (3,075 lb. Load Rating) * 4" Steel Channel Tongue * 2k Rated Setback Jack w/ Foot * A-Frame Posi-Lock Coupler * ...Over 4 weeks ago on RVUSATools
-
2003 Doolittle Cargo Trailer. Used very little. Had very little road time, tires like new. $2900.00 Near Vinton Email at tom@oaklandnaz,orgOver 4 weeks ago on ClazTools
-
For Sale: 1984 Nuwa Hitchiker II, 25FT Fith wheel camper. Sleeps 6, queen bed, gas stove and heat, electric cold ac and fridge, new front jacks, water pump and tires in 2013, good brakes, awning is very good condition, table and couch make into be...1 week ago on ClazTools
-
6' digging depth, 12" bucket W / 3 replaceable teeth, (Pengo 2300 series), boom constructed from 1/4 thick reinforced steel plate, comes equipped with Parker brand hoses, fittings & couplers (job site ready), oversized greasable pins, treaded step...Over 4 weeks ago on RVUSATools
-
* 3" x 2" x 3/16" Steel Angle Frame (Single Axle) * 4" x 3" x 1/4" Steel Angle Frame (Tandem Axle) * 3" x 2" x 3/16" Steel Angle Crossmembers * 4" Steel Channel Tongue * 2" x 1-1/2" Steel Tube Uprights * 2" x 2" Steel Tube Top Rail * 2" A-Frame Po...Over 4 weeks ago on RVUSATools
-
Fully enclosed cylinder , for pulling small trees & saplings, 1/2" thick steel plate on gripping teeth, comes equipped with Parker brand hoses, fittings, & couplers (job ready), 10 3/4" opening, treaded step, 4 rows of teeth, oversized greaseable ...Over 4 weeks ago on RVUSATools
-
Looking to sell or possibly trade my formula z 700. It's a very clean sled with almost a brand new inch and a quarter ripsaw track, brand new carbides and new seat. I'm wanting to upgrade to a rev chassis that's the reason I'm selling. Will entert...1 week ago on AmericanlistedTools
-
Up for sale is a 1997 kawasaki kx 100. Has hand guards and i put a new gold series chain on it about two years ago. Has good tires, good brakes, and runs good. Comes with an owners manual, a stock stand, and lift stand all three are in the picture...Over 4 weeks ago on ClazTools
-
Made in the U.S.A. Bolt on reversible edge, 3/16 thick sides, 3/16 thick bottom with wear bars for reinforcement, treaded step, 10" extended bottom, 3/4 thick x 6" wide cutting edge. Offered by: Patten EquipmentOver 4 weeks ago on RVUSATools
